| Device Properties |
| Property name |
Property type |
Description |
| Kz1_Factor |
Tango::DEV_DOUBLE |
Coefficient used with the dipole measurement mode
(AD) exterior blades |
| Kz2_Factor |
Tango::DEV_DOUBLE |
Coefficient used with the dipole measurement mode
(BC) exterior blades |
| Delta_Z |
Tango::DEV_DOUBLE |
Coefficient used with the dipole measurement mode |
| Ca |
Tango::DEV_DOUBLE |
current offset on electrode A. this is the current measured when the beam is cut |
| Cb |
Tango::DEV_DOUBLE |
current offset on electrode B. this is the current measured when the beam is cut |
| Cc |
Tango::DEV_DOUBLE |
current offset on electrode C. this is the current measured when the beam is cut |
| Cd |
Tango::DEV_DOUBLE |
current offset on electrode D. this is the current measured when the beam is cut |
| Ka |
Tango::DEV_DOUBLE |
GAIN correction of the electrode A |
| Kb |
Tango::DEV_DOUBLE |
GAIN correction of the electrode B |
| Kc |
Tango::DEV_DOUBLE |
GAIN correction of the electrode C |
| Kd |
Tango::DEV_DOUBLE |
GAIN correction of the electrode AGAIN correction of the electrode D |
| MisalignementOffset |
Tango::DEV_DOUBLE |
|
| ElectronicOffset |
Tango::DEV_DOUBLE |
|
| OperatorOffset |
Tango::DEV_DOUBLE |
operator offset |
| Locum4ProxyName |
Tango::DEV_STRING |
|
| LowVoltageThreshold |
Tango::DEV_DOUBLE |
if the input voltages of the ADC decrease this threshold, the corresponding
average current attributes become ALARM ( ex : if |Vmes| < low_threshold)
|
| HighVoltageThreshold |
Tango::DEV_DOUBLE |
if the input voltages of the ADC exceed this threshold, the corresponding
average current attributes become ALARM ( ex : if |Vmes| > threshold) |
| SaiControllerProxyName |
Tango::DEV_STRING |
name of the SaiController device proxy |
| OffsetZ1 |
Tango::DEV_DOUBLE |
offset on vertical position 1 |
| OffsetZ2 |
Tango::DEV_DOUBLE |
offset on vertical position 2 |
| Z1CorrectionTable |
Array of double |
offset list for Z1 position. one offset is associated to one gain.
Offset are ordered accortding increase gain order. |
| Z2CorrectionTable |
Array of double |
offset list for Z2 position. one offset is associated to one gain.
Offset are ordered accortding increase gain order. |
| XBPMVersion |
Tango::DEV_USHORT |
XBPM version. Value must be in range [1,2].
This property has no default value and must be defined. |
| Kx_Factor |
Tango::DEV_DOUBLE |
This property is only supported by the XBPM version 2
Defaults to 1.0 |
| Kz_Factor |
Tango::DEV_DOUBLE |
This property is only supported by the XBPM version 2
Defaults to 1.0 |
| MisalignementOffsetX |
Tango::DEV_DOUBLE |
This property is only supported by the XBPM version 2
Defaults to 0.0 |
| MisalignementOffsetZ |
Tango::DEV_DOUBLE |
This property is only supported by the XBPM version 2
Defaults to 0.0 |
| OffsetX |
Tango::DEV_DOUBLE |
This property is only supported by the XBPM version 2
Defaults to 0.0 |
| OffsetZ |
Tango::DEV_DOUBLE |
This property is only supported by the XBPM version 2
Defaults to 0.0 |
| OperatorOffsetX |
Tango::DEV_DOUBLE |
This property is only supported by the XBPM version 2
Defaults to 0.0 |
| OperatorOffsetZ |
Tango::DEV_DOUBLE |
This property is only supported by the XBPM version 2
Defaults to 0.0 |
| XCorrectionTable |
Array of double |
X gain correction table |
| ZCorrectionTable |
Array of double |
Z gain correction table |
| Formula |
Tango::DEV_USHORT |
0 : use old formula to compute beam position.
1 : use the new one. |
