| Device Properties |
| Property name |
Property type |
Description |
| InputRange |
Tango::DEV_STRING |
The signal input range.
Possible values are B_10, B_5, B_2_5, B_1_25, U_10, U_5, U_2_5, U_1_25. |
| DaqTimeOut |
Tango::DEV_DOUBLE |
this value must be higher than the buffer integration time. In fact a timeout call back
occured if no data are recieved since the time specified in this property |
| BoardType |
Tango::DEV_STRING |
ADLink ADC board type SAI_2005. default value SAI_2005 |
| BoardNum |
Tango::DEV_SHORT |
ADLink ADC board identifier in the CPCI crate. |
| Kz1_Factor |
Tango::DEV_DOUBLE |
Coefficient used with the dipole measurement mode
(AD) exterior blades |
| Kz2_Factor |
Tango::DEV_DOUBLE |
Coefficient used with the dipole measurement mode
(BC) exterior blades |
| Delta_Z |
Tango::DEV_DOUBLE |
Coefficient used with the dipole measurement mode |
| Ca |
Tango::DEV_DOUBLE |
current offset on electrode A. this is the current measured when the beam is cut |
| Cb |
Tango::DEV_DOUBLE |
current offset on electrode B. this is the current measured when the beam is cut |
| Cc |
Tango::DEV_DOUBLE |
current offset on electrode C. this is the current measured when the beam is cut |
| Cd |
Tango::DEV_DOUBLE |
current offset on electrode D. this is the current measured when the beam is cut |
| MisalignementOffset |
Tango::DEV_DOUBLE |
|
| Ka |
Tango::DEV_DOUBLE |
GAIN correction of the electrode A |
| Kb |
Tango::DEV_DOUBLE |
GAIN correction of the electrode B |
| Kc |
Tango::DEV_DOUBLE |
GAIN correction of the electrode C |
| Kd |
Tango::DEV_DOUBLE |
GAIN correction of the electrode AGAIN correction of the electrode D |
| ElectronicOffset |
Tango::DEV_DOUBLE |
|
| OperatorOffset |
Tango::DEV_DOUBLE |
operator offset |
| Locum4ProxyName |
Tango::DEV_STRING |
|
| Geometry |
Tango::DEV_SHORT |
you have to choose between 2 differents modes, either insertion or dipole mode.
According to the chosen mode the calculation of the beam position is different.
2 possible values
- 1 : insertion
- 2 : bipolar (source)
- 3: bipolar (proxima) |
| CurrentOffset1 |
Tango::DEV_DOUBLE |
current offset on channel 1 |
| CurrentOffset2 |
Tango::DEV_DOUBLE |
current offset on channel 2 |
| CurrentOffset3 |
Tango::DEV_DOUBLE |
current offset on channel 3 |
| CurrentOffset4 |
Tango::DEV_DOUBLE |
current offset on channel 4 |
| AlarmThresholdVoltage |
Tango::DEV_DOUBLE |
if input voltages of the ADC converter exceed this threshold, all current and voltage
attribute quality change to ALARM ( ex : if |Vmes| > threshold). |
| VerticalPositionFactor |
Tango::DEV_DOUBLE |
Vertical Position Factor
|
| VerticalPositionOffset |
Tango::DEV_DOUBLE |
Vertical Position Offset |
| HorizontalPositionFactor |
Tango::DEV_DOUBLE |
Hortizontal Position Factor |
| HorizontalPositionOffset |
Tango::DEV_DOUBLE |
Hortizontal Position Offset |
| VoltageOffset1 |
Tango::DEV_DOUBLE |
voltage offset on channel 1 |
| VoltageOffset2 |
Tango::DEV_DOUBLE |
Voltage Offset on channel 2 |
| VoltageOffset3 |
Tango::DEV_DOUBLE |
Voltage Offset on channel3 |
| VoltageOffset4 |
Tango::DEV_DOUBLE |
Voltage Offset on channel 4 |
| IntensityThreshold |
Tango::DEV_DOUBLE |
cuurent out of which the Measured Intensity has a meaning (in micro-A) |
